![]() It will be in left ear only but a quick hit on the "Mono" in the ControlRoom Settings fixes that and sends same signal to both ears.īUT I still can not record a WET signal to file other than enabling LOOPBACK inside AN 1/2 hardware output strip. ![]() I can also disable monitoring with TotalMix FX by turning the meters/sliders (including small fx slider) all the way down on AN 1 in the hardware inputs and then I just click the track "monitor" icon in Kristal Audio and I can hear myself in the headphones. OK, finally I got it working again, reset levels properly etc and now I can do Live Audio Monitoring with TotalMix FX both dry and wet/FX/reverb or combination of reverb+dry or just wet signal. This doesn't happen if I disable the "loopback" in hardware output it seems but then I miss out on recording the wet totalmix's reverb signal to file. The problem with this though is that when I try to record a Second Track inside Kristal Audio Engine (using ASIO) I get bleeding of the 1st track playing back into my second track recorded. So how should I record the TotalMix FX's Reverb or Echo so that my recorded WAVE file has a wet signal in it with the fx? I was able to do that only with KRISTAL AUDIO ENGINE not with AUDACITY, but I did it by enabling "loopback" in the TotalMixFX hardware output for Analog 1/2 of babyface. ![]() I was able to do this with Kristal Audio Engine with it's "monitor" feature on the track and Echo/Reverb disabled on the TotalMix, that way I can hear my dry voice in headphones for live "dry" monitoring, but this doesn't work with Audacity since it seems Audacity doesn't support ASIO so I was hoping I could just have TotalMixFx do it, and it works but only if I enable Reverb or Echo and I'd like to also be able to hear it dry since Audacity can't record TotalMix Reverb anyway, or can it?) (ALSO though, how do I do LIVE Audio Monitoring without Reverb or FX enabled? Right now I can only hear myself in the headphones if I have Reverb or Echo enabled in Totalmix, I have not figured out how to monitor myself Dry without reverb or echo with just TotalMix. ![]() So here's my problem now, I don't see how I can DISABLE the "through" audio so I don't hear myself in the headphones but to still have REVERB and AUDIO enabled so that I can RECORD the TotalMix FX "wet" signal. Well I finally found out that if I enabled REVERB or ECHO inside TotalMix FX, all the sudden I have Live Audio Monitoring in terms that I can hear in the headphones whatever I'm saying through the microphone in basically more or less realtime it seemed. I was using Audacity, tried many different things, 'software playback' in edit preferences, tried using computer built-in soundcard/interface for the audio monitoring but too much delay/latency so obviously I needed to get it to work through headphone jack direct on babyface. The next problem adding a couple more bumps on the head was getting Live Audio Monitoring to work. Strangely, TotalMixFX was also nowhere to be found to download even when going to the support website and selecting the Babyface product, all that was shown was the 1068 driver update, the firmware update download, and Digicheck download.įinally after doing some heavy googling, I found a link in a forum here to a zip file with TotalMixfix and after running that, like by magic suddenly we had Audio in the Headphones on playback etc. After lot of trial and error, and referencing manual finally I found out about "TotalMix Fx" which for some reason was nowhere on the CD that came with the Babyfaces. The first issue was that once setup there was no audio in the headphones, either one of them. I'm trying to properly setup a silver and blue babyface and have hit my head on the desk for quite some hours.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |